<menu id="uukow"></menu>
<nav id="uukow"><nav id="uukow"></nav></nav>
<nav id="uukow"><strong id="uukow"></strong></nav>
<nav id="uukow"></nav>
<menu id="uukow"><strong id="uukow"></strong></menu>

  • 東莞市廣豐聯泰塑料有限公司

    專供PC+ABS 沙伯基礎PC 德國拜耳PC+ABS 寶理PPS LCP

    產品分類
    聯系方式
    友情鏈接
    您當前的位置：首頁 » 新聞中心 » PBT+PC VALOX VX5022 玻璃纖維增強20%
    新聞中心
    PBT+PC VALOX VX5022 玻璃纖維增強20%
    發布時間：2016-04-19        瀏覽次數：285        返回列表
     

    VALOX ? Resin VX5022

    		SI | British | Metric | PDF Europe-Africa-Middle East: COMMERCIAL

     
    VALOX VX5022 is a 20% glass fibre reinforced PBT+PC blend with low warpage characteristics. This grade is 5021 with reduced warpage.
     

    Property
     
    TYPICAL PROPERTIES (1)
    MECHANICAL Value Unit Standard
    Tensile Stress, yld, Type I, 5 mm/min 1270 kgf/cm2 ASTM D 638
    Tensile Stress, brk, Type I, 5 mm/min 1270 kgf/cm2 ASTM D 638
    Tensile Strain, yld, Type I, 5 mm/min 3 % ASTM D 638
    Tensile Strain, brk, Type I, 5 mm/min 3 % ASTM D 638
    Tensile Modulus, 5 mm/min 74400 kgf/cm2 ASTM D 638
    Flexural Stress, yld, 1.3 mm/min, 50 mm span 1470 kgf/cm2 ASTM D 790
    Flexural Modulus, 1.3 mm/min, 50 mm span 59100 kgf/cm2 ASTM D 790
    Tensile Stress, yield, 5 mm/min 110 MPa ISO 527
    Tensile Stress, break, 5 mm/min 110 MPa ISO 527
    Tensile Strain, yield, 5 mm/min 3 % ISO 527
    Tensile Strain, break, 5 mm/min 3 % ISO 527
    Tensile Modulus, 1 mm/min 7100 MPa ISO 527
    Flexural Stress, yield, 2 mm/min 150 MPa ISO 178
    Flexural Stress, break, 2 mm/min 150 MPa ISO 178
    Flexural Strain, break, 2 mm/min 3 % ISO 178
    Flexural Modulus, 2 mm/min 6300 MPa ISO 178
    Hardness, H358/30 205 MPa ISO 2039-1
    Hardness, Rockwell R 122 - ISO 2039-2
    IMPACT Value Unit Standard
    Charpy Impact, unnotched, 23°C 55 kJ/m2 ISO 179/2C
    Charpy Impact, unnotched, -30°C 50 kJ/m2 ISO 179/2C
    Izod Impact, unnotched, 23°C 66 cm-kgf/cm ASTM D 4812
    Izod Impact, unnotched, -30°C 65 cm-kgf/cm ASTM D 4812
    Izod Impact, notched, 23°C 8 cm-kgf/cm ASTM D 256
    Izod Impact, notched, 0°C 8 cm-kgf/cm ASTM D 256
    Izod Impact, notched, -30°C 8 cm-kgf/cm ASTM D 256
    Instrumented Impact Total Energy, 23°C 662 cm-kgf ASTM D 3763
    Izod Impact, unnotched 80*10*4 +23°C 40 kJ/m2 ISO 180/1U
    Izod Impact, unnotched 80*10*4 -30°C 35 kJ/m2 ISO 180/1U
    Izod Impact, notched 80*10*4 +23°C 7 kJ/m2 ISO 180/1A
    Izod Impact, notched 80*10*4 0°C 7 kJ/m2 ISO 180/1A
    Izod Impact, notched 80*10*4 -30°C 6 kJ/m2 ISO 180/1A
    Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm 6 kJ/m2 ISO 179/1eA
    Charpy Impact, notched, 23°C 9 kJ/m2 ISO 179/2C
    Charpy -30°C, V-notch Edgew 80*10*4 sp=62mm 5 kJ/m2 ISO 179/1eA
    Charpy Impact, notched, -30°C 9 kJ/m2 ISO 179/2C
    Charpy 23°C, Unnotch Edgew 80*10*4 sp=62mm 40 kJ/m2 ISO 179/1eU
    Charpy -30°C, Unnotch Edgew 80*10*4 sp=62mm 40 kJ/m2 ISO 179/1eU
    THERMAL Value Unit Standard
    Vicat Softening Temp, Rate A/50 200 °C ASTM D 1525
    Vicat Softening Temp, Rate B/50 145 °C ASTM D 1525
    HDT, 0.45 MPa, 3.2 mm, unannealed 180 °C ASTM D 648
    HDT, 1.82 MPa, 3.2mm, unannealed 120 °C ASTM D 648
    CTE, -40°C to 40°C, flow 4.E-05 1/°C ASTM E 831
    CTE, -40°C to 40°C, xflow 1.E-04 1/°C ASTM E 831
    CTE, -40°C to 40°C, flow 2.49E-05 1/°C ISO 11359-2
    CTE, -40°C to 40°C, xflow 6.87E-05 1/°C ISO 11359-2
    CTE, 23°C to 60°C, flow 4.E-05 1/°C ISO 11359-2
    CTE, 23°C to 60°C, xflow 1.E-04 1/°C ISO 11359-2
    CTE, 23°C to 80°C, flow 4.E-05 1/°C ISO 11359-2
    CTE, 23°C to 80°C, xflow 1.E-04 1/°C ISO 11359-2
    CTE, 23°C to 150°C, flow 2.43E-05 1/°C ISO 11359-2
    CTE, 23°C to 150°C, xflow 1.12E-04 1/°C ISO 11359-2
    Ball Pressure Test, 125°C +/- 2°C PASSES - IEC 60695-10-2
    Vicat Softening Temp, Rate A/50 200 °C ISO 306
    Vicat Softening Temp, Rate B/50 145 °C ISO 306
    Vicat Softening Temp, Rate B/120 145 °C ISO 306
    HDT/Bf, 0.45 MPa Flatw 80*10*4 sp=64mm 180 °C ISO 75/Bf
    HDT/Af, 1.8 MPa Flatw 80*10*4 sp=64mm 120 °C ISO 75/Af
    PHYSICAL Value Unit Standard
    Specific Gravity 1.39 - ASTM D 792
    Filler Content 20 % ASTM D 229
    Mold Shrinkage on Tensile Bar, flow (2) (5) 0.3 - 0.8 % SABIC Method
    Mold Shrinkage, flow, 3.2 mm (5) 0.3 - 0.5 % SABIC Method
    Mold Shrinkage on Tensile Bar, xflow (2) (5) 0.5 - 0.9 % SABIC Method
    Melt Flow Rate, 250°C/2.16 kgf 16 g/10 min ASTM D 1238
    Melt Flow Rate, 265°C/5.0 kgf 50 g/10 min ASTM D 1238
    Melt Flow Rate, 266°C/5.0 kgf 50 g/10 min ASTM D 1238
    Density 1.39 g/cm3 ISO 1183
    Water Absorption, (23°C/sat) 0.1 % ISO 62
    Moisture Absorption (23°C / 50% RH) 0.06 % ISO 62
    Melt Volume Rate, MVR at 250°C/2.16 kg 13 cm3/10 min ISO 1133
    Melt Volume Rate, MVR at 250°C/5.0 kg 28 cm3/10 min ISO 1133
    Melt Volume Rate, MVR at 265°C/5.0 kg 40 cm3/10 min ISO 1133
    Melt Viscosity, 260°C, 1500 sec-1 215 Pa-s ISO 11443
    ELECTRICAL Value Unit Standard
    Volume Resistivity >1.E+15 Ohm-cm ASTM D 257
    Dielectric Strength, in oil, 0.8 mm 31 kV/mm ASTM D 149
    Dielectric Strength, in oil, 1.6 mm 28 kV/mm ASTM D 149
    Dielectric Strength, in oil, 3.2 mm 16 kV/mm ASTM D 149
    Relative Permittivity, 1 MHz 3.3 - ASTM D 150
    Dissipation Factor, 1 MHz 0.014 - ASTM D 150
    Hot Wire Ignition {PLC) 0 PLC Code UL 746A
    High Ampere Arc Ign, surface {PLC} 0 PLC Code UL 746A
    Volume Resistivity >1.E+16 Ohm-cm IEC 60093
    Surface Resistivity, ROA >1.E+16 Ohm IEC 60093
    Dielectric Strength, in oil, 0.8 mm 31 kV/mm IEC 60243-1
    Dielectric Strength, in oil, 1.6 mm 28 kV/mm IEC 60243-1
    Dielectric Strength, in oil, 3.2 mm 16 kV/mm IEC 60243-1
    Relative Permittivity, 100 Hz 3.3 - IEC 60250
    Relative Permittivity, 1 MHz 3.3 - IEC 60250
    Dissipation Factor, 50/60 Hz 0.001 - IEC 60250
    Dissipation Factor, 100 Hz 0.001 - IEC 60250
    Dissipation Factor, 1 MHz 0.014 - IEC 60250
    Comparative Tracking Index 250 V IEC 60112
    Comparative Tracking Index, M 100 V IEC 60112
    Relative Permittivity, 50/60 Hz 3.1 - IEC 60250
    FLAME CHARACTERISTICS Value Unit Standard
    UL Recognized, 94HB Flame Class Rating (3) 1.5 mm UL 94
    UL Recognized, 94HB Flame Class Rating 2nd value (3) 3 mm UL 94
    Glow Wire Flammability Index 750°C, passes at 1 mm IEC 60695-2-12
    Glow Wire Flammability Index 850°C, passes at 2 mm IEC 60695-2-12
    Oxygen Index (LOI) 23 % ISO 4589
    Source GMD, last updated:2015/11/02
    Processing

    Parameter
    Injection Molding Value Unit
    Drying Temperature 110 - 120 °C
    Drying Time 2 - 4 hrs
    Maximum Moisture Content 0.02 %
    Melt Temperature 250 - 270 °C
    Nozzle Temperature 240 - 260 °C
    Front - Zone 3 Temperature 245 - 265 °C
    Middle - Zone 2 Temperature 240 - 255 °C
    Rear - Zone 1 Temperature 230 - 245 °C
    Hopper Temperature 40 - 60 °C
    Mold Temperature 40 - 100 °C
    Source GMD, last updated:2015/11/02

    下一篇： 暫無相關信息！

    轉載請注明：轉載自環球塑化資訊網 http://www.cqzhejia.com/news/
    本文鏈接：http://www.cqzhejia.com/b-shabo/news269626/
    免責聲明：本文"PBT+PC VALOX VX5022 玻璃纖維增強20%"僅代表作者個人觀點，與環球塑化網無關。環球塑化網所轉載的內容，其版權均由原作者和資料提供方所擁有！如因作品版權問題需要處理，請與我們聯絡。電話：400-115-2868

    機械手 激光機
    ©2025 環球塑化網 版權所有   技術支持： 環球塑化網     訪問量：543035  管理入口

    收縮

    • 電話咨詢

    • 0769-82558310
    QR code
    關閉
    關閉
    請輸入驗證碼
    免费 无码 国产在线观看AV,日韩AV国语AV,日韩AV无码成人,无码精品日韩AV (function(){ var bp = document.createElement('script'); var curProtocol = window.location.protocol.split(':')[0]; if (curProtocol === 'https') { bp.src = 'https://zz.bdstatic.com/linksubmit/push.js'; } else { bp.src = 'http://push.zhanzhang.baidu.com/push.js'; } var s = document.getElementsByTagName("script")[0]; s.parentNode.insertBefore(bp, s); })();